# 01. Modular propagation station **PROTOTYPE / NOT PHYSICALLY TESTED** Six removable rooting cups in a shallow refillable tray, with an optional clear-film cover frame. ## Printable parts | STL | Quantity | Purpose / orientation | | --- | ---: | --- | | `stl/tray.stl` | 1 | 210 x 144 x 32 mm; open face upward; holds the raft on an internal shelf. | | `stl/raft.stl` | 1 | 203.2 x 137.2 x 4 mm; flat face down; six bevelled cup seats and a refill hole. | | `stl/cup.stl` | 6 | 50 mm maximum diameter, 25 mm high; perforated shallow rooting basket; upright. | | `stl/fill_cap.stl` | 1 | 22 mm diameter; print broad face on bed, turn over to insert. | | `stl/cover_post.stl` | 4 | Optional cover: 110 mm high, 8 mm main diameter; vertical with a brim or laid flat with supports. | | `stl/cover_frame.stl` | 1 | Optional cover: 210 x 144 x 6 mm; flat on bed. | ## Dimensions and interfaces - Tray: **210 x 144 x 32 mm**. Raft: **203.2 x 137.2 x 4 mm**. - Six cup centres: x = -61, 0, 61 mm; y = -31, 31 mm. - Cup body: 44 mm diameter; seat: 44.8 mm, with a matching bevel. Cup rim: 50 mm. - Water floor: z = 3 mm. Cup bottom: z = 7 mm when assembled. Raft top: z = 29 mm. - Cover posts: 5.8 mm pins in 6.4 mm sockets. Cover height: approximately 135 mm including the exposed top pins. - Refill stem: 15.4 mm into a 16 mm opening. No gasket or liquid seal is designed here. The refill cap is stored flat-face-down for printing and must be turned over to use. The frame and posts are optional; their listed quantity builds one complete covered station. Repeated stations remain independent and can be arranged side by side. ## Bought hardware and supplies - Optional: one sheet of clean clear horticultural film, about 500 x 450 mm, trimmed to suit; clip or tape to the cover frame without sealing all ventilation. - Optional: six rooting plugs sized to the 39 mm cup opening; supports or cuttings chosen for the plant. ## Assembly 1. Place the tray on a level, washable surface and check its floor and seams with plain water. 2. Drop the raft onto the shelf at z=25 mm, with the cup-seat bevels upward. The corner notches fit around the tray socket bosses. 3. Insert six cups. Their 44 mm bodies fit the 44.8 mm holes; matching bevels support their 50 mm rims at the raft surface. 4. Add water through the 16 mm refill hole. With the cups installed, their bottoms are at z=7 mm and the tray floor at z=3 mm. Start shallow and adjust water depth to the plant and rooting medium. 5. Turn the fill cap over and place its 15.4 mm stem into the refill hole. It is a loose cap, not a seal. 6. Optional: insert four cover posts into the tray sockets until their shoulders rest on the tray top. Put the cover frame onto the upper pins. Add bought clear film and leave vents; the printed frame itself is not transparent. ## Printing - All parts are millimetres. Trial settings: 0.20 mm layer height, four perimeters, five or six solid bottom layers and 20-30% infill. Adjust to your filament and slicer. - PETG is a starting material for a room-temperature wet prototype; do not assume any printed surface is leakproof or sanitary. - Tray, raft, cups, cap and frame are exported in their intended orientation. Cups have bevelled rims to reduce unsupported overhangs. Inspect the socket shelf in the slicer. - Cover posts are optional and slender. Print individually with a 5-8 mm brim and slow outer walls; alternatively lay them flat and support the pins, then remove and smooth supports. - Dry-fit one cup and one cover post first. Do not force pins or scale all assembled parts indiscriminately. ## Limits and first checks - PROTOTYPE / NOT PHYSICALLY TESTED. Clearances, wet durability and actual print settings need confirmation. - This is a shallow passive propagation tray, not an aeroponic cloner. No pump, heater, transparent cover or plant material is included. - Six cups are 39 mm inside diameter and approximately 20 mm deep below their rims. Larger rooting plugs require an edited raft and cup together. - The cover has no hinge or rigid transparent panels. Film and attachment method are external supplies. ## Editing and exporting Open `design.scad` in OpenSCAD and select a named `part`. The `preview` selector shows an assembly for reference and is not a printable part. All STL coordinates are millimetres. ```bash openscad -D 'part="tray"' -o tray.stl design.scad ``` After changing interfaces, export both mating parts and inspect them in your slicer. The root `tools/export_all.py` can regenerate the whole pack. Mesh closure does not prove a printed vessel is leakproof.